Did you know?

If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ...Litter-Robot 4 user? Visit is user guide on troubleshooting Litter-Robot 4 lights. Litter-Robot 3 lights: Quickness download guide. If you’re looking for a quick download guide on all the Litter-Robot 3 lights, download the digital guide here conversely click on the image under. Litter-Robot 3 flashing blue light If your Litter-Robot is slowly flashing yellow or stuck upside down due to the cat sensor, complete the troubleshooting steps in our Litter-Robot 3: Yellow light flashing (Cat sensor) guide. If your Litter-Robot is flashing red or stuck upside down, complete the troubleshooting steps in our Litter-Robot 3: Red light flashing (Cat sensor fault ... Preparation. Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three sensors located in the top of the ...Replace the bonnet by inserting the bonnet tabs into the rear bonnet slots, then press the latches while rotating it forward until the latches click into place. From the Home position, press the Reset button to zero the weight sensors. The Litter-Robot should return home displaying a blue 'ready light' status.May 29, 2022 ... Want to keep your Litter-Robot 3 running perfectly, and avoid those nasty flashing error lights? Performing simple monthly maintenance is ... Litter-Robot 3: Yellow flashing slowly (Cat sensor) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second. This will also occur if the cat sensor is activated by a cat ... The Litter Robot 3 control panel provides the main user input /(buttons) and output (LEDs) for the robot. Aside from the main power light, there are three lights on the Litter Robot 3 control panel, which are blue (ready button), yellow (cycling button) and red (timing button). There are also four buttons which are "power", "cycle", "empty" and ...In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...The unit will cycle again 15 seconds after your cat has left the globe or 5 seconds after the bonnet is replaced. If your Litter-Robot is not detecting your cat or not cycling, complete the troubleshooting steps in our Litter-Robot 3: Cat not detected guide. If your Litter-Robot is slowly flashing yellow or stuck upside down due to the cat ...Put the globe in with the key on an angle to fit into the notch to the left. Put bonnet back on. Then turn the key to the locked position. Replug in and it should cycle automatically. Hope this helps! Solid yellow light also could mean its in sleep cycle. If you hold the cycle button it should shut off.Bili lights are a type of light therapy (phototherapy) that is used to treat newborn jaundice. Jaundice is a yellow coloring of the skin and eyes. It is caused by too much of a yel...Kurupt_Introvert. •. Flashing yellow to red means the motor has detected an obstruction or jam. Turn the unit off and remove the bonnet and globe. Check for gear or motor obstruction. Reassemble the unit and verify a proper litter level. Then turn the unit on—if the problem persists, try the Litter-Robot 3 Troubleshooter or contact Whisker ...Preparation. Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three sensors located in the top of the ...*The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by excess weight. Please remove excess weight and check your unit for the following: The litter is above the fill line or in excess of 10lbs. The cat sensor has not been reset after adding weightCat sensor troubleshooting. In this article we will troubleshoot the "Bonnet removed" message. If you received a "Cat sensor interrupt" notification in the Whisker app, refer to the Litter-Robot 3: Yellow flashing slowly (Cat sensor) guide. If …Reply. litterrobot. •. That Blue flash followed by the rapid Yellow flash is indicative of a failure in the Drawer Full Indicators and Pinch Detect Terminals. If your Litter-Robot is in Warranty, give our Customer Experience Specialists a call at 877.250.7729.If you've completed this troubleshooting and your Litter-Robot is still flashing yellow, you will need either a new bonnet or a new base. If your issue was a result of a bonnet malfunction, you'll need a bonnet replacement. If your issue was a result of a cat sensor malfunction, you'll need a base replacement. What do I do? The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ... Troubleshooting. If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch safety feature and you will need to inspect the pinch sensor. Inspect the sensors. The purpose of the pinch sensor is to detect if an object is blocking the waste port during the globe rotation.Hi @Christos93. Please check also anti-pinch pins. The Anti-Pinch safety feature is two pins connected to the motherboard that must touch each other continuously. If they are separated, you will have an alarm (yellow blinking light). The Anti-Pinch safety is located in the top back left of the Litter-Robot base. The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red. Blink cameras are a popular choice for home security systems, providing users with peace of mind and the ability to monitor their property remotely. However, one common issue that ...I went to the litter robot Support and filled theCame home to my Litter-Robot in the upside Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode. If it cannot cycle after three attempts, the globe will return to t Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Got questions or issues? Contact Litter-Robot Support today. We’re dedicated to ensuring a seamless experience for you & your pet. Disconnect the litter box and turn it on af

If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by excess weight.Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Resolve the 'Accessory not detected' issue on your Litter-Robot 4, indicated by an alternating blue and purple light bar, with our visual troubleshooting guide.The Litter-Robot is equipped with an Anti-Pinch Safety Feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch conditi... If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app. You can now proceed with the onboarding process within the Whisker App to finalize connection. Used your step by step directions and was able to replace motor and wire harness in my cats litter robot 2. When I connected the litter robot to power supply yellow soild light then red solid light motor would not turn. Thankfully, I had not put the top andd bottom together.

When I turn on the Litter Robot 3 (non-connect), blue light is flashing, then I press Reset and fast yellow light is flashing. When I press Reset again, blue light is flashing and so on.. What I checked so far: - Anti Pinch Pins looks good and are touching each other. - DFI is clean and 4 IR LEDs are blinking once a second.Troubleshooting. If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch safety feature and you will need to inspect the pinch sensor. Inspect the sensors. The purpose of the pinch sensor is to detect if an object is blocking the waste port during the globe rotation.If the night light turns on and the cycle is interrupted, then your bonnet needs to be replaced. It is possible that the night-light is not even working, in this case, please remove the power from the robot and unclip the bonnet. Inside the bonnet, you will see 2 wires connected to a small circuit.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. If your Litter-Robot 3 is displaying a yellow light . Possible cause: If your unit displays a yellow ping-pong light bar, this indicates that .